Aluminium alloy foams are a form of porous metal whose structure resembles the shape of natural
materials such as coral, bone, sponge, etc. Due to their structure, these materials retain good
mechanical properties of the base material while being significantly lighter than non-porous metal.
Metal foams can be used as energy and vibration absorbers, heat exchangers, insulators, and filters.
The main disadvantage of this type of material is its high production cost. To reduce production
costs, aluminium alloy chips are used as base material. Foams are made of A360 and AA 7075
aluminium alloys. To produce a porous structure, CaCO3 is used as a foaming agent while Zn and
CaOwere added as stabilizing agents. The main goal of the paper was to investigate the difference
in the shape of pores and relative density after foaming with different stabilizing agents.
References
1.
N. M, M MS. H.: Comparison of the Energy Absorption of Closed-Cell Aluminum Foam Produced by Various Foaming Agents. Strength Mater. 2016;48(3):444-449,.
2.
R. FM, R. RAH, H ES. Effect of Zinc Content on the Mechanical Properties of Closed-Cell Aluminum Foams,Int. J Met. 2021;
3.
K. G, B. L, S. J, J K. Aluminium foams made of various aluminium alloys scrap and various foaming agents. Mechanical Technology and Structural Materials. 2022;37-42,.
4.
S. T, M. K, N K. Producing technology of aluminum foam from machined chip waste, Mater. Trans. 2006;47(9):2125-2130,.
5.
V. KGS, F. GM, J B. Kennedy A.: The stabilising effect of oxides in foamed aluminium alloy scrap. Int J Mater Res. 2015;106(9):978-987,.
6.
T.N. PK, S V. Seetharamu S.: Effect of Grain Size of Calcium Carbonate Foaming Agent on Physical Properties of Eutectic Al–Si Alloy Closed Cell Foam, Trans. Indian Inst Met. 2015;68(1):109-112,.
7.
H. JA, H AE. Farhan K.: Modelling and optimization of manufacturing calcium carbonate-based aluminum foam, Mater. Res Express. 2019;6(8).
8.
H. W, F. ZD, S. H, H. YD, G. NT, Z L. P.: Cellular structure and energy absorption of Al–Cu alloy foams fabricated via a two-step foaming method. Mater Des. 2020;196.
9.
Sudharsan TR, Vinod-Kumar GS. Optimizing the hot compaction parameters of Al-Mg-Cu foams processed through elemental powder route. IOP Conf Ser Mater Sci Eng. 2018;402(1).
10.
F. AM, A. E, A. FN, J. GL, W. HJ, N WH. Metal foams: a design guide. 2002;23(1).
11.
V. K, D. SS, I. P, B. S, M J. Synthesis and Characterisation of Closed Cells Aluminium Foams Containing Dolomite Powder As Foaming Agent. Mater Tehnol. 2010;44(6):363-371,.
12.
J. A, C. C, M Z. Effect of CaCO3 content change on the production of closed-cell aluminum foam by selective laser melting. Opt Laser Technol. 2020;141(November):107097,.
13.
P. PD, H. O, F. S, A. TS, N M. The use of dolomite as foaming agent and its effect on the microstructure of aluminium metal foams-Comparison to titanium hydride, Colloids Surfaces A Physicochem. Eng Asp. 2011;382(1–3):118-123,.
14.
Karuppasamy R. Barik D.: Production methods of aluminium foam: A brief review, Mater. Today Proc. 2020;37(Part 2):1584-1587,.
15.
A. B, B G. Structural and physicomechanical characterization of closed-cell aluminum foams with different zinc additions, Sci. Eng Compos Mater. 2018;25(4):789-795,.
16.
H. A, A. G, A. NM, G K. Mankovits T.: Effect of the manufacturing parameters on the pore size and porosity of closed-cell hybrid aluminum foams. Int Rev Appl Sci Eng. 2021;12(3):230,.
17.
MartínE P. Microstructural parameters affecting the compressive response of closedcell aluminum foams, Mech. Adv Mater Struct. 2021;1-20,.