ADSORPTION OF COPPER IONS FROM AQUEOUS SOLUTIONS USING SUNFLOWER HEADS AS AN ADSORBENT
In this paper, the results of changes in pH and conductivity values of the solutions during the rinsing of the adsorbent, as well as during the adsorption of copper ions were presented. Prior to the adsorption experiments, the sunflower heads were rinsed with 200 cm3 of distilled water in ten equal portions (20 cm3 each). After each water volume pa...
By Milan Gorgievski, Nada Štrbac, Velizar Stanković, Vesna Grekulović, Miljan Marković, Dragana Božić
INFLUENCE OF Na2SiO3/NaOH RATIOS ON THE COMPRESSIVE STRENGTH OF FLY ASH BASED GEOPOLYMERS FROM THERMAL POWER PLANT STANARI IN BIH
In this paper, the influence of Na2SiO3 /NaOH ratio on the compressive strength of fly ash - based geopolymers was tested. The fly ash from thermal power plant Stanari near Doboj, BiH is used.The ratio of alkali activator to fly ash (AA / FA ratio) was constant in all samples and it was 0.8. A 12M NaOH solution was used. The heat treatment temperat...
By Nadira Bušatlić, Ilhan Bušatlić, Nevzet Merdić, Dženana Smajić-Terzić
WHAT ELIMINATORY ECO TEST OF MOTOR VEHICLES SHOULD BRING?
In order to reduce the harmful effects of exhaust gases on the environment, as of January 1, 2017, at all stations for technical inspection of vehicles, during the regular technical inspection of vehicles, the contents of motor vehicle exhausts are also carried out - EKO test. According to the Rulebook on Exhaust Gas Testing of Motor Vehicles (ECO ...
By Dragana Agić, Fuad Klisura
EFFECT OF NANOSILICA ADDITION ON CONCRETE POROSITY AND SORPTIVITY
This paper presents an experimental investigation into the effect of nanosilica addition to porosity and capillary absorption of concrete. Three concrete mixtures 0%, 2%, and 4% nanosilicaby weight of cementweretested.The procedure described in ASTM C642-06 was used to determine the total volume of permeable voids.Water absorption and the rate of w...
By Adnan Mujkanovic, Anesa Ključanin, Marina Jovanović, Amel Zahirović, Amna Karić, Nevzet Merdić
TOXICOLOGICAL ASPECTS OF FOOD PAPER PACKING
Mostly used food packing are: paper, cartoon, plastics, glass, metals and multilayer materials. The plastics and paper/cartoon make about 70% of all food packing. These two have the biggest migration potential. The use of plastics is regulated by specific EU rules, but it is not yet the same about the use of paper packing. In order to ensure health...
By Benjamin Muhamedbegović, Midhat Jašić, Marizela Šabanović, Faik Uzunović
THE QUALITY OF THE PULP WASHING PRODUCED BY THE SULPHATE PROCESS IN THE CELLULOSE AND PAPER FACTORY "NATRON HAYAT", MAGLAJ
The process of the pulp washing is very important both economically and environmentally, since the quality of cellulose washing is directly related to the efficiency of chemical regeneration and the quality of the wastewater generated. The purpose of the cellulose fiber washing process is to economically remove the maximum of soluble organic and so...
By Azra Halilović, Ilhan Bušatlić, Šefkija Botonjić, Amna Karić
EFFECT OF DISPERSANT ON GROUND GRANULATED BLASTFURNACE SLAG PARTICLE SIZE DISTRIBUTION DETERMINED BY LASER DIFFRACTION METHOD
Particle size distribution measurements were performed on ground granulated blastfurnace slag by laser diffraction with the powder dispersed in distilled water with sodium hexametaphosphate used as dispersing agent, as well as in pure distilled water and propan-2-ol. Two samples of slag with Blaine fineness 4700 cm2 /g and5500 cm2 /g were tested.Th...
By Adnan Mujkanovic, Marina Jovanović, Amel Zahirović, Mustafa Hadžalić, Nevzet Merdić
CALIBRATION OF TEST DEVICE FOR MICROHARDNESS TESTING
Proper calibration of the device is important to prevent potential sources of error, which ensures that the test results most effectively represent the value of the sample being tested. In microhardness testing, the loading force does not exceed 1.96 N. The test surface requires a more complex metallographic preparation, and the smaller the injecti...
By Edib Horoz, Belma Fakić, Adisa Burić, Mirsada Oruč
INVESTIGATION THE POSSIBILITY OF POZZOLANIC CEMENT CEM IV 42,5N PRODUCTION IN CEMENT PLANT KAKANJ
This paper presents an experimental study to evaluate the possibility of CEM IV 42,5N producing by increasing the specific cement surface from 3180 to 3850 cm2 /g. In this paper, fly ash is used as a cement admixture because fly ash possesses both hydraulic and pozzolanic properties. If one part of the clinker, as a major cement admixture, is repla...
By Nevzet Merdić, Nedžad Haračić, Ilhan Bušatlić, Nadira Bušatlić, Amna Karić
CHAMOTTE REFRACTORY CASTABLE PROPERTIES ENHANCING BY OPTIMIZING PARTICLE SIZE DISTRIBUTION
The paper examined the changes in properties of conventional castables composed of a mixture of calcium-aluminate cement and chamotte caused by changes in the particle size distribution. Properties of castable with 20 % cement and „as received“ chamotte were compared with castableofparticle size distribution adapted to the calculated di...
By Marina Jovanović, Adnan Mujkanovic