Home Archive News Contact
More Filters
METALLIC AND NONMETALLIC MATERIALS

Vol 14, Issue 1,2023

METALLIC AND NONMETALLIC MATERIALS

Vol 13, Issue 1,2021

METALLIC AND NONMETALLIC MATERIALS

Vol 12, Issue 1,2018

METALLIC AND NONMETALLIC MATERIALS

Vol 11, Issue 1,2016

METALLIC AND NONMETALLIC MATERIALS

Vol 10, Issue 1,2014

Some specific aspects in positioning of the re-heating furnaces at a layout of different rolling mills, for a period of about last hundred years in rolling mills practice are presented in this paper. Practical solutions in the above mentioned (a.m.) field are presented for the different rolling mills. Some of the a.m. aspects are explained, confirm...

By Omer Beganović, Faik Uzunović

28.05.2021. Professional paper Metallic materials
EFFECT OF HEAT TREATMENT ON MICROSTRUCTURE AND HARDNESS OF STEEL 67SiCr5

Steel 67SiCr5 is a alloyed carbon steel usually used for production of springs. It is used for load bearing springs, ring-shape springs, spiral springs, anti vibration springs etc. Springs steels are usually distribute in annealed or hardened and tempered state. Heat treating could be performed before or after springs forming. In this article, the ...

By Almaida Gigović-Gekić, Jusuf Duraković, Hasan Avdušinović

The chemical composition of casting is an important factor affecting the shape of graphite and the mechanical properties and microstructure of the metal base. Different elements have different influence to casting properties. All elements that affect the microstructure development during casting solidification have significant influence on mechanic...

By Aida Imamović, Hasan Avdušinović, Anida Henjaković

28.05.2021. Professional paper Metallic materials
TREATMENT OF SAE 1006 STEEL BILLETS WITH AND WITHOUT BORON ADDITION

This work aims at the development of low-carbon steel SAE 1006 through the microalloying addition of boron. Boron as alloying element is added in small amount, but it has significant effect on changes of properties of this kind of steel. The research is based on mechanical and microstructural testing of final product (wire) from the aspect of the i...

By Aida Imamović, Alma Puljić, Omer Kablar

Many researches are done for finding various ways of improving steel properties, since it's the most used material in the world. Instead of using high-alloyed steels, which are expensive, microalloying of carbon steels that will retain equal properties is an efficient replacement. For this research it was tested melts of low-carbon steel grade SAE ...

By Aida Imamović, Adna Puljić, Omer Kablar

Dual phase steels are low carbon steels which are thermo-mechanically processed to getting better formability and toughness than ferrite-perlite steels with similar tensile strength. The microstructure of these steels consisting of a ferrite matrix with hard martensitic/ bainitic second phase. The concept of representative volume element (RVE) is c...

By Emina Vardo, Aida Imamović, Jessica Gola

28.05.2021. Research article Metallic materials
CALIBRATION OF TEST DEVICE FOR MICROHARDNESS TESTING

Proper calibration of the device is important to prevent potential sources of error, which ensures that the test results most effectively represent the value of the sample being tested. In microhardness testing, the loading force does not exceed 1.96 N. The test surface requires a more complex metallographic preparation, and the smaller the injecti...

By Edib Horoz, Belma Fakić, Adisa Burić, Mirsada Oruč

Some specific aspects in positioning of the re/heating furnaces at a layout of the modern rolling mills are presented in this paper. Theoretical and practical solutions in the above mentioned (further a.m.) field are presented for both, wire rod and light section bar mills. Some of the a.m. aspects are explained, confirming that even unexpected sol...

By Omer Beganović, Faik Uzunović

In the technology of bentonite mixture mold unexplored fields are the properties of a mixture of a quartz sand fraction 0.106 mm, 0.3 mm and 0.425 mm and the possibility of stacking in horizontal layers in the mold. The investigation is related to the layers of the following combination of sand fractions: 0.3 / 0.106 / 0.425 mm, 0.106 / 0.425 / 0.3...

By Ajla Huseljić, Ana Beroš, Hasan Avdušinović

Gypsum is added to the Portland cement clinker in the amount of 3 to 5% in the grinding phase as the binding rate regulator. When it comes to the hydration of cement, if sufficient amount of gypsum is added, fast cementation will not occur because gypsum by its presence reduces the solubility of tricalcium aluminate and thus slows down rapid reacti...

By Ilhan Bušatlić, Amna Karić

Conference of University of Zenica