Home Archive News Contact
More Filters
METALLIC AND NONMETALLIC MATERIALS

Vol 15, Issue 1,2025

METALLIC AND NONMETALLIC MATERIALS

Vol 14, Issue 1,2023

METALLIC AND NONMETALLIC MATERIALS

Vol 13, Issue 1,2021

METALLIC AND NONMETALLIC MATERIALS

Vol 12, Issue 1,2018

METALLIC AND NONMETALLIC MATERIALS

Vol 11, Issue 1,2016

METALLIC AND NONMETALLIC MATERIALS

Vol 10, Issue 1,2014

28.05.2021. Professional paper Environment protection and sustainable development
ADSORPTION OF COPPER IONS FROM AQUEOUS SOLUTIONS USING SUNFLOWER HEADS AS AN ADSORBENT

In this paper, the results of changes in pH and conductivity values of the solutions during the rinsing of the adsorbent, as well as during the adsorption of copper ions were presented. Prior to the adsorption experiments, the sunflower heads were rinsed with 200 cm3 of distilled water in ten equal portions (20 cm3 each). After each water volume pa...

By Milan Gorgievski, Nada Štrbac, Velizar Stanković, Vesna Grekulović, Miljan Marković, Dragana Božić

In this paper, the influence of Na2SiO3 /NaOH ratio on the compressive strength of fly ash - based geopolymers was tested. The fly ash from thermal power plant Stanari near Doboj, BiH is used.The ratio of alkali activator to fly ash (AA / FA ratio) was constant in all samples and it was 0.8. A 12M NaOH solution was used. The heat treatment temperat...

By Nadira Bušatlić, Ilhan Bušatlić, Nevzet Merdić, Dženana Smajić-Terzić

28.05.2021. Professional paper Environment protection and sustainable development
WHAT ELIMINATORY ECO TEST OF MOTOR VEHICLES SHOULD BRING?

In order to reduce the harmful effects of exhaust gases on the environment, as of January 1, 2017, at all stations for technical inspection of vehicles, during the regular technical inspection of vehicles, the contents of motor vehicle exhausts are also carried out - EKO test. According to the Rulebook on Exhaust Gas Testing of Motor Vehicles (ECO ...

By Dragana Agić, Fuad Klisura

28.05.2021. Professional paper Nonmetallic materials
EFFECT OF NANOSILICA ADDITION ON CONCRETE POROSITY AND SORPTIVITY

This paper presents an experimental investigation into the effect of nanosilica addition to porosity and capillary absorption of concrete. Three concrete mixtures 0%, 2%, and 4% nanosilicaby weight of cementweretested.The procedure described in ASTM C642-06 was used to determine the total volume of permeable voids.Water absorption and the rate of w...

By Adnan Mujkanovic, Anesa Ključanin, Marina Jovanović, Amel Zahirović, Amna Karić, Nevzet Merdić

28.05.2021. Professional paper Environment protection and sustainable development
TOXICOLOGICAL ASPECTS OF FOOD PAPER PACKING

Mostly used food packing are: paper, cartoon, plastics, glass, metals and multilayer materials. The plastics and paper/cartoon make about 70% of all food packing. These two have the biggest migration potential. The use of plastics is regulated by specific EU rules, but it is not yet the same about the use of paper packing. In order to ensure health...

By Benjamin Muhamedbegović, Midhat Jašić, Marizela Šabanović, Faik Uzunović

The process of the pulp washing is very important both economically and environmentally, since the quality of cellulose washing is directly related to the efficiency of chemical regeneration and the quality of the wastewater generated. The purpose of the cellulose fiber washing process is to economically remove the maximum of soluble organic and so...

By Azra Halilović, Ilhan Bušatlić, Šefkija Botonjić, Amna Karić

Particle size distribution measurements were performed on ground granulated blastfurnace slag by laser diffraction with the powder dispersed in distilled water with sodium hexametaphosphate used as dispersing agent, as well as in pure distilled water and propan-2-ol. Two samples of slag with Blaine fineness 4700 cm2 /g and5500 cm2 /g were tested.Th...

By Adnan Mujkanovic, Marina Jovanović, Amel Zahirović, Mustafa Hadžalić, Nevzet Merdić

28.05.2021. Research article Metallic materials
CALIBRATION OF TEST DEVICE FOR MICROHARDNESS TESTING

Proper calibration of the device is important to prevent potential sources of error, which ensures that the test results most effectively represent the value of the sample being tested. In microhardness testing, the loading force does not exceed 1.96 N. The test surface requires a more complex metallographic preparation, and the smaller the injecti...

By Edib Horoz, Belma Fakić, Adisa Burić, Mirsada Oruč

This paper presents an experimental study to evaluate the possibility of CEM IV 42,5N producing by increasing the specific cement surface from 3180 to 3850 cm2 /g. In this paper, fly ash is used as a cement admixture because fly ash possesses both hydraulic and pozzolanic properties. If one part of the clinker, as a major cement admixture, is repla...

By Nevzet Merdić, Nedžad Haračić, Ilhan Bušatlić, Nadira Bušatlić, Amna Karić

The paper examined the changes in properties of conventional castables composed of a mixture of calcium-aluminate cement and chamotte caused by changes in the particle size distribution. Properties of castable with 20 % cement and „as received“ chamotte were compared with castableofparticle size distribution adapted to the calculated di...

By Marina Jovanović, Adnan Mujkanovic

Conference of University of Zenica