FINE ALUMINUM HYDROXIDE PRECIPITATION FROM SODIUM ALUMINATE LEACH LIQUOR
Fine alumina trihydrate (ATH) is the primary filler of environmentally acceptable flame retardants, artificial agate, and other products, in addition to being the raw material for alumina-based ceramics and catalyst carriers. This study aims to investigate the fine aluminum trihydrate precipitation process from sodium aluminate Bayer leach liquor b...
By Sıla Meva Elitaş, Batuhan Dikici, Ali Ergüzeloğlu, Bayram Güneş, Hatice Kubra AKBEN
EFFECT OF MIXING OF COOLING MEDIA ON MICROSTRUCTURE AND HARDNESS OF STEEL 23MnB4
Steel cooling is an important technological operation because the final microstructure of the steel,and therefore its properties, depends on the cooling rate. The speed of steel cooling depends onnumerous factors, one of which is the movement of the cooling media. This paper presents theresults of testing the influence of mixing the cooling media o...
By Almaida Gigovic-Gekic, Hasan Avdušinović, Amna Hodzić, Branka Muminović
THE INFLUENCE OF ALLOYING ELEMENTS TO CAST IRON MICROSTRUCTURE
Gray cast iron belongs to the group of iron casts that contain graphite particles in the microstructure. Graphite particles in gray cast iron have the shape of lamellae and are connected to each other. The specific combination of properties of gray cast iron, which is satisfactory for many applications, and simple and cheap productio...
By Anida Henjaković, Hasan Avdušinović, Amir Muslić
CHARACTERISTICS OF THE MICROSTRUCTURE AND GRAIN SIZE OF S690QL STEEL IN THE HARDENED AND TEMPERED STATE
Steel S690 QL is a high-strength quenched and tempered, fine-grained structural steel with a minimum yield strength of ReH of 690 MPa and with guaranteed toughness (Charpy) for rolled plates with a thickness of 3 to 50 mm. This paper presents the examination and analysis of the microstructure and grain size results after quenching an...
By Mirsada Oruč, Aida Imamović, Almaida Gigovic-Gekic, Milenko Rimac
DEVELOPMENT OF NEW CEMENT TYPE CEM II/C-M ACCORDING TO EN 197-5
According to new EN 197-5 is possible to combine clinker with blast furnace slag, silica fume,pozzolana, fly ash, burnt shale, and limestone from 36 – 50% while clinker content should be from50 – 64%. In this paper are presented results of laboratory testing concerning CEM II/C-M(S+W) production where a sample is prepared by mixing 50% ...
By Nedžad Haračić, Nevzet Merdić, Ilhan Bušatlić, Nadira Bušatlić
STRENGTH DEVELOPMENT OF CONCRETE CONTAINING GROUND GRANULATED BLAST FURNACE SLAG FROM ARCELORMITTAL ZENICA AS A PARTIAL CEMENT REPLACEMENT
The strength development of concrete containing ground granulated blast-furnace slag (GGBS), aby-product of iron in blast-furnace, as a partial substitute for cement,was experimentally studied.Levels of replacement of cement by slag were 12.5 %, 25 %, 37.5 %, and 50 % by weight ofcement. Slag taken immediately after it was discharged from the blast...
By Adnan Mujkanovic, Marina Jovanović, Nadira Bušatlić, Amel Zahirović, Anesa Bitić, Nevzet Merdić
CALCULATION OF THERMAL CONDUCTIVITY FOR CRYSTALLINE NANOSTRUCTURES
We have introduced a theory for the calculation of thermodynamic characteristics for somecharacteristic nanostructures (ultrathin films and superlattices), using the adapted method of twotimetemperature Green's functions. In this paper, we have determined the coefficient of thermalconductivity using the definition of free energy and then compared t...
By Siniša M. Vučenović, Jovan P. šetrajčić
ANALYSIS OF THE ORIGIN OF AIR POLLUTION IN THE AREA ZENICA-DOBOJ CANTON
The paper presents data on emissions of analyzed pollutants into the air (SO2, NOx, CO, VOC,NH3, PM10, PM2.5, PAH, Pb, Cd, and Hg) by sector (industry and energy, small combustion plants,road traffic and services-agriculture and animal husbandry), and by cities and municipalities inthe area of the Zenica-Doboj Canton. Based on the analyzed data, it...
By Vehid Birdahić, Muvedet Šišić, Nusret Imamović, Halim Prcanović, Mirnes Duraković
RESEARCH OF THE POSSIBILITY OF USING THE HEAT GENERATED IN THE AEROBIC BIODEGRADATION PROCEDURE
The paper describes the research methodology of the heat generated by the biologicaldecomposition of a mixture of sludge from WTP (wastewater treatment plant) and biowaste and itsuse outside the system for a controlled biodegradation process. Earlier research in this area definedthe optimal mixtures of sludge and biowaste that ensure quality manage...
By Muvedet Šišić, Vehid Birdahić, Sanela Beganović, Mirnes Duraković, Farzet Bikić
THE ROLE OF WOOD-BASED PRODUCTS IN SUSTAINABLE DEVELOPMENT
Wood is renewable, recyclable, climate-friendly material, and presents an important segment inachieving circular economy and sustainability concepts. To be able to link these two concepts,production and consumption systems need to transform towards sustainability. Wood-basedproducts play a role in mitigating climate change by reducing carbon from t...
By Petar Ćurić, Jelena Obranković, Andreja Pirc-Barčić