The calibration measurement capability - CMC is defined as the smallest uncertainty that a laboratory can achieve within its powers when carried out more or less daily calibration of nearly ideal measurement standards intended to define, generate, keep or renew units of that size, or one or more of its value, or when carried out more...

By Branka Muminović, Mirsada Oruč, Almaida Gigović-Gekić, Raza Sunulahpašić

This paper examines the impact of charging wet and oxidized material on the quality of cast iron, quality SL20. In consideration were taken the same products obtained from 3 melts. For the production of the first melt wet and oxidized charging components in quantity of 60 % were used, for the second one quantity of 20 % of oxidizied ...

By Ajla Huseljić, Aida Mahmutović, Hasan Avdušinović

There is something inherent, compelling and mystified in ruins and remains of the old fort. The issues logically imposed at the first encounter with these witnesses of the past are linked to their current condition, age and role in history. Historically, all those fortresses were more than the fortified military structure. They have ...

By Amir Čaušević, Nerman Rustempašić, Lana Kudumović

The effect of fly ash, coal dust and limestone on the properties of brick products are presented in this paper. Three kinds of clay were used to test the effect of additives. There were investigated the effect  of additives on the behaviour of clays during drying and firing (shrinkage and loss of weight), and the  properties of fired samp...

By Marina Jovanović, Adnan Mujkanović, Erna Tutić, Vedija Karalić

Refractory materials are an important part of industrial furnaces and metallurgical aggregates. With time and use, the wear out of refractory materials ocures and their replacement becomes necessary. Part of refractory material, which is removed after the demolition of industrial furnaces and metallurgical unit refractory linings, represents refrac...

By Menzur Plaćo, Omer Kablar

The paper presents preliminary analysis of the impact of the season and time of day on the content of benzene, toluene, ethylbenzene and xylene in the air of the city of Zenica. This analysis is carried out on the basis of data on the measurement of concentrations of benzene, toluene, ethylbenzene and xylene downloaded from the Metallurgical Instit...

By Farzet Bikić, Asim Ibrahimagić, Hasnija Berbić, Halim Prcanović

The review of long-lasting investigations at Department of Metallurgical Engineering, Technical Faculty in Bor, University of Belgrade in the field of thermodynamics and phase diagrams of numerous gallium-based systems is presented in this paper. The results of investigation of some binary and ternary systems, obtained experimentally...

By Dragana Živković

Partially crystalline metallic glass ZrCu was prepared in the form of ribbons by melt-spinning. The chemical composition and homogeneity of the samples alongside partial crystallinity with the existence of an amorphous matrix was confirmed. The measured value of microhardness shows a nonlinear dependence with the increase of Cu. By adding a small f...

By Kerim Hrvat, Amra Salčinović Fetić, Ljerka Slokar, Matej Lozančić, Andrija Franjković, Senad Hatibović, Suada Sulejmanović

This study has examined the process of sintering of Mg0 samples (80 % precipitation) obtained from seawater at a temperature of 1600 ºC with time until the sintering temperature is obtained, in order to examine their properties (density, porosity) and chemical composition after sintering. The prepared magnesium oxide samples are distinguished ...

By Miroslav Labor, Marina Perić, Jelena Jakić, Vanja Martinac

Opencast mines are a part of the systems with the worst influence on all environmental components (air, water, ground, flora and fauna). In the case that we completely left out safeguards, dust emission would have a significant impact on the health of employees and the local population. Dust emission from quarries belongs to fugitive emissions and ...

By Šefket Goletić, Amina Ahmić