Particle size distribution measurements were performed on ground granulated blastfurnace slag by laser diffraction with the powder dispersed in distilled water with sodium hexametaphosphate used as dispersing agent, as well as in pure distilled water and propan-2-ol. Two samples of slag with Blaine fineness 4700 cm2 /g and5500 cm2 /g were tested.Th...

By Adnan Mujkanovic, Marina Jovanović, Amel Zahirović, Mustafa Hadžalić, Nevzet Merdić

This paper presents an experimental study to evaluate the possibility of CEM IV 42,5N producing by increasing the specific cement surface from 3180 to 3850 cm2 /g. In this paper, fly ash is used as a cement admixture because fly ash possesses both hydraulic and pozzolanic properties. If one part of the clinker, as a major cement admixture, is repla...

By Nevzet Merdić, Nedžad Haračić, Ilhan Bušatlić, Nadira Bušatlić, Amna Karić

The paper examined the changes in properties of conventional castables composed of a mixture of calcium-aluminate cement and chamotte caused by changes in the particle size distribution. Properties of castable with 20 % cement and „as received“ chamotte were compared with castableofparticle size distribution adapted to the calculated di...

By Marina Jovanović, Adnan Mujkanovic

In this paper, we have introduced new contemporary materials for heat harvesting, based on thermoelectric effect (or Seebeck effect): rear earth mono-pnictides and graphene. Measure of effectiveness for transformation of heat to electricity is represented with zT factor, which measure heat harvesting potential. zT factor is related with heat and el...

By Siniša M. Vučenović, Jovan P. Šetrajčić, Steva K. Jaćimovski

This paper presents an experimental investigation into the effect of nanosilica addition to porosity and capillary absorption of concrete. Three concrete mixtures 0%, 2%, and 4% nanosilicaby weight of cementweretested.The procedure described in ASTM C642-06 was used to determine the total volume of permeable voids.Water absorption and the rate of w...

By Adnan Mujkanovic, Anesa Ključanin, Marina Jovanović, Amel Zahirović, Amna Karić, Nevzet Merdić

In this paper, the influence of Na2SiO3 /NaOH ratio on the compressive strength of fly ash - based geopolymers was tested. The fly ash from thermal power plant Stanari near Doboj, BiH is used.The ratio of alkali activator to fly ash (AA / FA ratio) was constant in all samples and it was 0.8. A 12M NaOH solution was used. The heat treatment temperat...

By Nadira Bušatlić, Ilhan Bušatlić, Nevzet Merdić, Dženana Smajić-Terzić

The presented investigation work investigates thermal properties of the ultra-high hardness (UHH) armour steel. Steel is distinguished with high hardness and strength. It is sold in the quenched or tempered state, because achieving planned hardness which has to be between 590 HB and 640 HB. In the frame of the investigation work the analysis of the...

By Borut Kosec, Tjaša Kranjec, Blaž Karpe, Aleš Nagode, Milan Bizjak, Jure Bernetič, Mirko Gojić, Zijah Burzić, Milan Rimac, Gorazd Kosec

Mine development imposes very high technical requirements of the mine hoisting equipment in terms of speed of transport. To meet these requirements it is necessary to properly design the structural elements of mine hoisting equipment which means that they must have the proper characteristics of the materials from which they are made such as mechani...

By Mustafa Hadžalić, Mirsada Oruč, Raza Sunulahpašić

Thermal properties and microstructure of the Sn-10% Ag and Sn-20% Ag alloys were experimentally investigated in this study. Melting behavior of the alloys were studied using differential scanning calorimetry (DSC). Microstructure of the alloys was analyzed by optical microscopy. The xenon-flash method was used for the measurements of thermal diffus...

By Dragan Manasijević, Ljubiša Balanović, Ivana Marković, Duško Minić, Aleksadar Đorđević

Surface roughness is the totality of microgeometric irregularities on the surface of an object and it is caused by various factors, from which the most important are machining and processing techniques. This characteristic of the material is very important, especially in the case of high-quality materials designed for the demanding conditions of ex...

By Raza Sunulahpašić, Mirsada Oruč, Edina Karić