The paper describes the behavior of welded joints of NN-70 steel in the presence of a cracking error when bending with impact force. The experiment was performed with three groups of test tubes, depending on the cut-off point of the test tube notch with the tip of the crack in BM, in WM and in HAZ. The test method used was conducted on the instrume...

By Nermin Bišćević

The basic characteristics of the chemical composition of steel with improved machinability (X8CrNiS18-9) are the increased content of sulphur (0.15-0.45%), phosphorus (0.07-0.11%) and manganese (0.5-1.5%). Sulphur by creating sulphide inclusions reduces friction and cutting resistance, and increases the brittleness of the chip.Considering its harmf...

By Derviš Mujagić, Aida Imamović, Mustafa Hadžalić

 In modern times, the science of materials cannot be imagined without metallography. The history of metallographic testing in Bosnia and Herzegovina is primarily related to Zenica. Today, most of the research related to the metal industry in BiH is conducted in laboratories at the Kemal Kapetanović Institute in Zenica. The Institute's Metallog...

By Belma Fakić, Adisa Burić, Edib Horoz

Steel 67SiCr5 is a alloyed carbon steel usually used for production of springs. It is used for load bearing springs, ring-shape springs, spiral springs, anti vibration springs etc. Springs steels are usually distribute in annealed or hardened and tempered state. Heat treating could be performed before or after springs forming. In this article, the ...

By Almaida Gigović-Gekić, Jusuf Duraković, Hasan Avdušinović

The precipitation of sigma (σ) phase in austenitic stainless steels is a significant subject of many investigations. Exposure of these steels to elevated temperatures (from 600 °C to 900 °C) results in precipitation of σ phase (transformation product from delta (δ) ferrite) which is one of the main reasons for the deterior...

By Amna Hodžić, Almaida Gigovic-Gekic, Raza Sunulahpašić

Mine development imposes very high technical requirements of the mine hoisting equipment in terms of speed of transport. To meet these requirements it is necessary to properly design the structural elements of mine hoisting equipment which means that they must have the proper characteristics of the materials from which they are made such as mechani...

By Mustafa Hadžalić, Mirsada Oruč, Raza Sunulahpašić

Thermal properties and microstructure of the Sn-10% Ag and Sn-20% Ag alloys were experimentally investigated in this study. Melting behavior of the alloys were studied using differential scanning calorimetry (DSC). Microstructure of the alloys was analyzed by optical microscopy. The xenon-flash method was used for the measurements of thermal diffus...

By Dragan Manasijević, Ljubiša Balanović, Ivana Marković, Duško Minić, Aleksadar Đorđević

In this paper, the results of changes in pH and conductivity values of the solutions during the rinsing of the adsorbent, as well as during the adsorption of copper ions were presented. Prior to the adsorption experiments, the sunflower heads were rinsed with 200 cm3 of distilled water in ten equal portions (20 cm3 each). After each water volume pa...

By Milan Gorgievski, Nada Štrbac, Velizar Stanković, Vesna Grekulović, Miljan Marković, Dragana Božić

Mostly used food packing are: paper, cartoon, plastics, glass, metals and multilayer materials. The plastics and paper/cartoon make about 70% of all food packing. These two have the biggest migration potential. The use of plastics is regulated by specific EU rules, but it is not yet the same about the use of paper packing. In order to ensure health...

By Benjamin Muhamedbegović, Midhat Jašić, Marizela Šabanović, Faik Uzunović

The process of the pulp washing is very important both economically and environmentally, since the quality of cellulose washing is directly related to the efficiency of chemical regeneration and the quality of the wastewater generated. The purpose of the cellulose fiber washing process is to economically remove the maximum of soluble organic and so...

By Azra Halilović, Ilhan Bušatlić, Šefkija Botonjić, Amna Karić