The paper describes the behavior of welded joints of NN-70 steel in the presence of a cracking error when bending with impact force. The experiment was performed with three groups of test tubes, depending on the cut-off point of the test tube notch with the tip of the crack in BM, in WM and in HAZ. The test method used was conducted on the instrume...

By Nermin Bišćević

The chemical composition of casting is an important factor affecting the shape of graphite and the mechanical properties and microstructure of the metal base. Different elements have different influence to casting properties. All elements that affect the microstructure development during casting solidification have significant influence on mechanic...

By Aida Imamović, Hasan Avdušinović, Anida Henjaković

Steel 67SiCr5 is a alloyed carbon steel usually used for production of springs. It is used for load bearing springs, ring-shape springs, spiral springs, anti vibration springs etc. Springs steels are usually distribute in annealed or hardened and tempered state. Heat treating could be performed before or after springs forming. In this article, the ...

By Almaida Gigović-Gekić, Jusuf Duraković, Hasan Avdušinović

The precipitation of sigma (σ) phase in austenitic stainless steels is a significant subject of many investigations. Exposure of these steels to elevated temperatures (from 600 °C to 900 °C) results in precipitation of σ phase (transformation product from delta (δ) ferrite) which is one of the main reasons for the deterior...

By Amna Hodžić, Almaida Gigovic-Gekic, Raza Sunulahpašić

Mine development imposes very high technical requirements of the mine hoisting equipment in terms of speed of transport. To meet these requirements it is necessary to properly design the structural elements of mine hoisting equipment which means that they must have the proper characteristics of the materials from which they are made such as mechani...

By Mustafa Hadžalić, Mirsada Oruč, Raza Sunulahpašić

In order to reduce the harmful effects of exhaust gases on the environment, as of January 1, 2017, at all stations for technical inspection of vehicles, during the regular technical inspection of vehicles, the contents of motor vehicle exhausts are also carried out - EKO test. According to the Rulebook on Exhaust Gas Testing of Motor Vehicles (ECO ...

By Dragana Agić, Fuad Klisura

Mostly used food packing are: paper, cartoon, plastics, glass, metals and multilayer materials. The plastics and paper/cartoon make about 70% of all food packing. These two have the biggest migration potential. The use of plastics is regulated by specific EU rules, but it is not yet the same about the use of paper packing. In order to ensure health...

By Benjamin Muhamedbegović, Midhat Jašić, Marizela Šabanović, Faik Uzunović

In this paper, the results of changes in pH and conductivity values of the solutions during the rinsing of the adsorbent, as well as during the adsorption of copper ions were presented. Prior to the adsorption experiments, the sunflower heads were rinsed with 200 cm3 of distilled water in ten equal portions (20 cm3 each). After each water volume pa...

By Milan Gorgievski, Nada Štrbac, Velizar Stanković, Vesna Grekulović, Miljan Marković, Dragana Božić

The process of the pulp washing is very important both economically and environmentally, since the quality of cellulose washing is directly related to the efficiency of chemical regeneration and the quality of the wastewater generated. The purpose of the cellulose fiber washing process is to economically remove the maximum of soluble organic and so...

By Azra Halilović, Ilhan Bušatlić, Šefkija Botonjić, Amna Karić

The application of nanotechnology in medicine and dentistry will bring significant advances in the diagnosis, treatment, and prevention of disease. Various applications of nanotechnology in medicine are responsible for development of a new branch of medicine, called nanomedicine, which shows how it is possible to improve the understanding of pathop...

By Vukoman Jokanović