Metallic materials thanks to the excellent combination of data on material properties are obtained by standardized and agreed testing of samples made from semi-finished or finished products. Metallic materials can be tested by different testing techniques. One of them is metallographic testing, for which a light microscope is used as a basic device...

By Adisa Burić, Belma Fakić, Edib Horoz, Mirsada Oruč

Some specific aspects in positioning of the re-heating furnaces at a layout of different rolling mills, for a period of about last hundred years in rolling mills practice are presented in this paper. Practical solutions in the above mentioned (a.m.) field are presented for the different rolling mills. Some of the a.m. aspects are explained, confirm...

By Omer Beganović, Faik Uzunović

Some specific aspects in positioning of the re/heating furnaces at a layout of the modern rolling mills are presented in this paper. Theoretical and practical solutions in the above mentioned (further a.m.) field are presented for both, wire rod and light section bar mills. Some of the a.m. aspects are explained, confirming that even unexpected sol...

By Omer Beganović, Faik Uzunović

Proper calibration of the device is important to prevent potential sources of error, which ensures that the test results most effectively represent the value of the sample being tested. In microhardness testing, the loading force does not exceed 1.96 N. The test surface requires a more complex metallographic preparation, and the smaller the injecti...

By Edib Horoz, Belma Fakić, Adisa Burić, Mirsada Oruč

Dual phase steels are low carbon steels which are thermo-mechanically processed to getting better formability and toughness than ferrite-perlite steels with similar tensile strength. The microstructure of these steels consisting of a ferrite matrix with hard martensitic/ bainitic second phase. The concept of representative volume element (RVE) is c...

By Emina Vardo, Aida Imamović, Jessica Gola

Some specific aspects in the improvement processes related to I-beams production, especially related to the conversion of classical to the universal rolling mills stands are presented in this paper. One of practical solutions in the a.m. conversion is described in some more details, as well as some of better designs in the variety of I-beams, conce...

By Faik Uzunović, Omer Beganović, Lamija Sušić

In this paper, we have introduced new contemporary materials for heat harvesting, based on thermoelectric effect (or Seebeck effect): rear earth mono-pnictides and graphene. Measure of effectiveness for transformation of heat to electricity is represented with zT factor, which measure heat harvesting potential. zT factor is related with heat and el...

By Siniša M. Vučenović, Jovan P. Šetrajčić, Steva K. Jaćimovski

This paper presents an experimental study to evaluate the possibility of CEM IV 42,5N producing by increasing the specific cement surface from 3180 to 3850 cm2 /g. In this paper, fly ash is used as a cement admixture because fly ash possesses both hydraulic and pozzolanic properties. If one part of the clinker, as a major cement admixture, is repla...

By Nevzet Merdić, Nedžad Haračić, Ilhan Bušatlić, Nadira Bušatlić, Amna Karić

The paper examined the changes in properties of conventional castables composed of a mixture of calcium-aluminate cement and chamotte caused by changes in the particle size distribution. Properties of castable with 20 % cement and „as received“ chamotte were compared with castableofparticle size distribution adapted to the calculated di...

By Marina Jovanović, Adnan Mujkanovic

Particle size distribution measurements were performed on ground granulated blastfurnace slag by laser diffraction with the powder dispersed in distilled water with sodium hexametaphosphate used as dispersing agent, as well as in pure distilled water and propan-2-ol. Two samples of slag with Blaine fineness 4700 cm2 /g and5500 cm2 /g were tested.Th...

By Adnan Mujkanovic, Marina Jovanović, Amel Zahirović, Mustafa Hadžalić, Nevzet Merdić